Hoyles Aidalarm Disabled Toilet Alarm Kit with Panic Stri User Manual

Browse online or download User Manual for Safety Hoyles Aidalarm Disabled Toilet Alarm Kit with Panic Stri. Hoyles Aidalarm Disabled Toilet Alarm Kit with Panic Strip User Manual [it]

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
The AIDALARM is designed as a disabled person alarm system primarily The Pull Cord S1600 should be appropriately sited for your application in
for use in WCs etc..It is designed to comply with BS8300 and the the WC or where assistance is required. Additional pull cords if required
requirements of the Disability Discrimination Act. are available separately. The lower bangle on the cord should be set at
100mm above floor level. The second bangle should be set between 800
The AIDALARM A600L controller should be sited where staff are located and 1000mm above floor level.
who can respond to an emergency call. It is usually powered by 230vac. The Reset Button S1708A should be sited near the point of call and
Standby batteries are included and there is an integral battery fault should be mounted with the bottom edge between 800 and 1000mm
monitor. Alternatively it can be powered by 12vdc, in this case the standby above floor level and a minimum of 350mm from any corner.
batteries should not be fitted, the battery fault monitor disabled (see later) The Overdoor Light/Sounder S1778A is usually sited outside and above
and a 12vdc PSU with standby battery used instead. The system voltage the WC door.
is 12vdc thus the ancillary items in toilets or other wet areas are at a safe DADO Panic Strip (Optional) is a normally open device, the contacts
working voltage avoiding any conflict with Part P building regulations. close when the switch is pressed. Site 150mm from floor level in WCs.
Mains Powered AIDALARM A600L Installation Instructions
Wiring details
Standard 6 core intruder alarm cable or similar is ideal to connect the AIDALARM controller to the ancillary items. The mains supply, when used, should
2
be 1mm twin and earth from a suitable 3A fused spur.
ve
-
ve
+
ve
+
A600L Controller
Located in responders
area
16vac from
Mains
transformer
N.O
COM
N.C.
L+ve
L-ve
BZ1
L7
L8
R11
LED6
B
W
Y
NC
NC
L5
L6
NO
COM
B
W
Y
COM
NO
LED5
+
R8
ZD1
PB1
L1P2P1
BZ
Pull Cord S1600
Overdoor Light/Buzzer
S1778A
Located outside WC
Reset Button S1708A
Located inside WC
BZ1
L7
L8
R11
R12
R14
R7
R3
R5
R6
LED6
LED4
LED2
LED8
B
W
Y
NC
NC
L5
L6
NO
COM
B
W
Y
COM
NO
LED5
LED3
LED1
LED7
+
R8
ZD1
L1 L2
BZ
N E L
Use six core intruder
alarm cable or similar
DADO Panic Strips (optional)
021-485SE
NO
Com
NC
Call
Com
Reset
SDR
-ve
LED
-ve
Fn
Bk Pp Rd
Battery
Connections
Set
Use
[
[
Set Button
PB1
PB2
Call LED
Power LED
-ve
+ve
-ve
+ve
Auxillary 12vdc output
when powered by mains, max 150mA.
12vdc input if powering
from a 12vdc power supply.
Volt free auxiliary
relay contacts
change on alarm
and mains fail
60129 Iss 1 June 2011
T. 01744 886600 F. 01744 886607 E. [email protected] W. www.hoyles.com
Hoyles Electronic Developments Ltd
Operation
Reset buttons and Overdoor units are fitted with LEDs and buzzers. Pull Cords are fitted with an LED. Additional units can be fitted if required. Silence
buttons S1703PR can also be fitted to give a more flexible operation. Consult our technical dept.
Battery Test
It is possible to test the standby batteries by pressing and holding the control p illuminated
indicates the batteries are very low, three LEDs indicate that the batteries are partly discharged and four LEDs indicate that the batteries are healthy.
Using the factory default settings, when a call is generated by pulling the cord or by activating any optional call accessory such as panic strip, audible and
visual warning is given at both the WC area and at the AIDALARM control panel. The call can be silenced at the control panel by pressing the control panel
button which is located at the centre of the LED diamond. This will cause the panel to bleep every 40 seconds as a warning of non attendance by the
responders. The audible indicators at the WC will bleep every five seconds to re-assure the caller. Should the cord be pulled again while in the Silence
state, the system will call again. The system is reset at (or near) the point of call using the Reset button S1708A.
anel button at the centre of the LED diamond. One LED
Technical Features
Battery Monitoring
The AIDALARM control panel when powered by mains should be fitted with 6 x AA alkaline batteries to provide backup in the event of a mains failure. The
control panel monitors the health of these batteries. When the batteries reach the end of their life, the control panel will beep and momentarily flash the
green power LED every 3 minutes. This prompts the system operator to have the batteries replaced. Good quality alkaline batteries should be used. It is
recommended that these batteries are replaced every 12 months during a regular maintenance inspection. The battery monitoring function should be
disabled when powering the system from a 12vdc power supply (See programming section). It can also be disabled if you do not wish to install batteries in
the system when powering from the mains, however this is not recommended.
Mains Failure
Should the mains supply to the control panel fail for any reason, as long as backup batteries are fitted the system will indicate the mains failure by beeping
every 90 seconds. The green power LED will also extinguish and flash momentarily every 90 seconds. In addition the alarm relay will also change state.
Alarm Relay
A single pole change over volt free relay is provided in the control panel. This relay is energised while the system is in its idle state, when a call is made the
relay de-energises, the relay energises again once the call has been reset. The relay also de-energises if the mains fails. Should a call be raised during a
mains failure, the relay will not change state.
Page view 0
1 2

Summary of Contents

Page 1 - Use six core intruder

The AIDALARM is designed as a disabled person alarm system primarily The Pull Cord S1600 should be appropriately sited for your application in for us

Page 2 - Also available from Hoyles

ProgrammingAll settings made in programming mode will be maintained in memory even if power and batteries are removed. The following features of the s

Comments to this Manuals

No comments